Introduction

Flashiibo Pro’s main purpose is to emulate NTAG215 which is the NFC technology amiibo figures use. However, it’s capable of emulating other NFC/RFID technologies.

For example, it’s also capable of emulating Mifare Mini, the NFC/RFID technology D. Infinity figures use. You may follow the following instructions to emulate D. Infinity.

Install the Latest Firmware

Make sure you are on firmware version 26.2.15 or later. See firmware upgrade instructions here.

How to Upload D. Infinity NFC Dumps

You can do this via the app.flashiibo.com/ website using a computer or laptop with Bluetooth.

  1. On your Flashiibo Pro with the latest firmware, navigate to the “Other RFID/NFC” menu.
    • If it’s your first time accessing this menu, it may take a while to initialize.
    • The device will also create a “chameleon” folder with two subfolders: “dumps” and “slots”.
  2. Return to the main menu and select the “User Manual” or “Manual & Bluetooth” option.
  3. Open app.flashiibo.com and connect it to your Flashiibo Pro device.
    • Check this guide for more detailed instructions using the tool.
  4. Click the “Refresh” button, and you should see contents of drive “E:/” appear.
  5. Inside this drive, locate the “chameleon” folder and its “dumps” subfolder.
    • These were automatically created in Step 1 when the “Other RFID/NFC” menu was initialized.
    • If you skipped Step 1, you can manually create these folders.
  6. In the “chameleon/dumps” folder, click the blue “Upload” button.
  7. Select the desired dumps from the Infinity Ultimate NFC Pack.
    • You can upload multiple dumps, but avoid uploading more than 20 at once or having too many dumps in this directory.
  8. The upload popup window can be a bit tricky.
    • Wait for all the dumps to upload, indicated by a green check mark on the right.
  9. Once complete, close the window.
    • You’ll get a warning message, simply confirm by clicking OK.
  10. All your uploaded dumps should now appear in the “chameleon/dumps” folder.

How to Emulate D. Infinity NFC Dumps

  1. On your Flashiibo Pro device, go to the “Other RFID/NFC” menu.
  2. Select “Slot 01”, then go to “Type” and make sure “Mifare Mini DI” is the type of this slot.
  3. Navigate to “Data…”, then “Load…”.
  4. Select a D. Infinity dump from the “chameleon/dumps” folder and you should see “Load File Success”.
  5. The following 3 steps are OPTIONAL because it’s done automatically. But if you run into issue, you can double check.
  6. Navigate to “Advanced…” and change “Custome Mode” should be [ON].
  7. Go one step down to “Load from block 0…” and activate it. It should say “Block 0 load success”
  8. Go one more step down to “ID Size” and check that it’s 7 Bytes.
  9. That’s it! You don’t need to adjust anything else. Simply return to “[Tag Details]” menu.
  10. You should now see your D. Infinity Figure’s name (with the file extension removed).
    • This is the emulation screen, and your Flashiibo Pro device will now emulate the selected Infinity figure.
    • To use a different figure, select a different slot and repeat the steps.
  11. Place your Flashiibo Pro device on the Infinity Base to bring the selected Infinity Figure into the game.

Notes

  • Do not use more than 1.5 MB of the device’s total 1.83 MB capacity.
    • Exceeding this limit may lead to hard bricking of the microcontroller, causing constant freezing on startup, among other issues.
    • Additionally, the device may slow down if you store too many small files.
  • Avoid placing too many files in the same directory.
  • Use short file and directory names to ensure the full file path does not exceed 64 characters.